白鐵風管能不能作為通風管？

發布人：http://hwzxw.net   發布時間：2022-03-21 16:53:30

外觀上沒有明顯的劃痕，簡單的說就是在白鐵風管內表面，我們看不到明顯的洞口和折痕，雖然不能說折痕就是壞，但確實影響美觀，會讓人懷疑質量。通風管廠家

There are no obvious scratches on the appearance. In short, we can't see obvious holes and creases on the inner surface of the white iron air duct. Although we can't say that the crease is bad, it does affect the beauty and make people doubt the quality. Ventilation pipe manufacturer

二是厚度，一般廠家在客戶要求下會把普通白鐵板材加工成管材，但有些劣質商家會做手腳，用薄板材代替厚板材。

The second is thickness. General manufacturers will process ordinary white iron plates into pipes at the request of customers, but some low-quality merchants will do hands and feet and replace thick plates with thin plates.

那佛山白鐵風管能不能作為通風管？

Can Foshan white iron air duct be used as a ventilation pipe?

要了解通風管路現場的工作條件，一般通風管路的要求不太嚴格，除了一些空氣中含有腐蝕性成分的現場應選擇不銹鋼管。

First of all, understand the working conditions of the ventilation pipeline on site. Generally, the requirements of the ventilation pipeline are not too strict. Except for some sites with corrosive components in the air, stainless steel pipes should be selected.

白色鐵風管的制造方法：

Manufacturing method of white iron air duct:

查看風管板放樣是否符合風管板制造任務單的要求，劃線是否正確，板有無損壞。

Check whether the setting out of the air duct board meets the requirements of the air duct board manufacturing task list, whether the marking is correct and whether the board is damaged.

檢查刀片是否有牢固的切削刃裝置。

Check whether the blade has a firm cutting edge device.

查看刀片的伸出高度是否與要求相符。直刀刨刀片的伸出高度應能堵住扳材，不會對桌面造成傷害；單刀刨刀片和雙刀刨刀片的伸出高度應能堵住上層鋁箔和芯材，不會對下層鋁箔造成傷害。雙面刨刀的間距約2毫米。

Check whether the extension height of the blade meets the requirements. The protruding height of the straight knife planer blade shall be able to block the pulling material and will not cause damage to the desktop; The protruding height of single knife planer blade and double knife planer blade shall be able to block the upper aluminum foil and core material without damaging the lower aluminum foil. The spacing between double-sided planers is about 2mm.

根據切邊要求選擇左邊的45°單刀刨或右邊的45°單刀刨。不銹鋼通風管道哪家好

Select the 45 ° single blade planer on the left or the 45 ° single blade planer on the right according to the trimming requirements. Which is a good stainless steel ventilation pipe

將鋁板置于工作臺上，用方鋁尺將鋁板平行固定在合適的方位。

Place the aluminum plate on the workbench and fix the aluminum plate in a proper position in parallel with a square aluminum ruler.