水菜丽加勒比av在线播放-国产精品一区二区三区综合-国产精品一区二区久久不-欧美国产精品亚洲精品观看

當前位置:首頁-新聞中心新聞中心

通風管道加工的注意事項有哪些?

發布人:http://hwzxw.net   發布時間:2022-08-19 17:12:46

現在通風管道大家都現已了解了吧,在建筑業快速展開的現在,高層建筑越來越多,為了保護在內工作人員的身體健康,通風管道的運用也多了起來,在給通風管道加工時,有許多事項要注意,下面主要是一些常見的問題:

Now we all know about the ventilation ducts. With the rapid development of the construction industry, there are more and more high-rise buildings. In order to protect the health of the staff inside, the use of ventilation ducts is also increasing. There are many matters to pay attention to when processing the ventilation ducts. The following are some common problems:

1、通風管道加工的過程中應該盡量防止呈現縱向接縫,可是必定不能呈現橫向接縫。并且通風管道的咬口縫和四角的縫隙處,需求依照規劃潔凈等級要求,然后還要選用密封膠將其堵嚴。其他通風管道板材的銜接縫的密封面應該設在通風管道壁的正壓側。

  1. Longitudinal joints shall be prevented as much as possible during the processing of ventilation pipes, but transverse joints shall not be allowed. In addition, the undercut joints and the four corners of the ventilation pipe shall be sealed with sealant according to the requirements of the planned cleanliness level. The sealing surface of the joint of other ventilation duct plates shall be set at the positive pressure side of the ventilation duct wall.

    QQ截圖20170428145524.png

2、加工的時分,不能在通風管道內部設置加固框或許加固筋,由于這樣關于通風管道的質量會造成必定的影響。

2. During processing, it is not allowed to set reinforcement frame or reinforcement bar inside the ventilation duct, because the quality of the ventilation duct will be affected.

3、通風管道加工不能選用S型插條和C型直角插條的銜接辦法,其他關于一些特其他通風管道來說,還不能選用按扣式的咬口。

3. The connection method of S-type and C-type right angle inserts cannot be selected for the processing of ventilation pipes. For other special ventilation pipes, the snap type bite cannot be selected.

4、通風管道制作結束之后,還要用清洗液進行清洗,只要到達清洗規范之后,才可以及時封口。

4. After the ventilation pipe is manufactured, it should be cleaned with cleaning liquid. As long as the cleaning specification is reached, it can be sealed in time.

5、假設是五顏六色涂層鋼板通風管道的話,應該堅持內壁是潤滑的,并且通風管道加工的過程中,還不能將涂層損壞,若是呈現損壞的部位,需求用環氧樹脂涂刷在表面即可。其他通風管道加工的過程中,還要做好防腐蝕措施,不能使用抽芯鉚釘,并且在通風管道零件安裝的時分,這些零件都要通過鍍鋅處理才行。

5. If it is a colorful coated steel plate ventilation pipe, the inner wall should be kept lubricated, and the coating should not be damaged during the processing of the ventilation pipe. If the damaged part appears, it needs to be painted on the surface with epoxy resin. During the processing of other ventilation pipes, anti-corrosion measures shall be taken, and blind rivets shall not be used. Besides, during the installation of ventilation pipe parts, these parts shall be galvanized.

如果做到以上問題不出錯的話,在給通風管道加工時應該沒有多大問題!

If the above problems are not wrong, there should be no big problem when processing the ventilation duct!

以上就是為大家介紹的有關濟南鐵皮風管加工的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://hwzxw.net

The above is the detailed introduction about the processing of Jinan iron sheet air duct. I hope it will help you. If you have any questions, please contact us. We will provide you with services with a professional attitude http://hwzxw.net


上一篇:排煙管道幾種保溫方式與標準
下一篇:工業空調的通風管道加工規范及注意事項是什么?

網站首頁 關于我們 產品展示 新聞中心 工程案例 在線留言 聯系我們

葫芦岛市| 阿拉善右旗| 枣强县| 平武县| 盐亭县| 长葛市| 苍溪县| 仙游县| 北宁市| 兴仁县| 遂昌县| 调兵山市| 扶绥县| 桓台县| 漾濞| 讷河市| 天等县| 车险| 诏安县| 资源县| 台北市| 迁西县| 溧阳市| 益阳市| 宜君县| 云林县| 扎兰屯市| 肇源县| 林甸县| 法库县| 通化市| 河津市| 中卫市| 隆安县| 上高县| 麻阳| 仲巴县| 利川市| 射阳县| 韩城市| 肃宁县|