白鐵皮通風管道加工制作的四大要求

發布人：http://hwzxw.net   發布時間：2023-06-19 13:55:23

外觀檢查：白鐵皮通風管道制作時，其所用板材、型材以及其他主要成品材料制作要求十分嚴格。焊縫應作外觀檢查，不應有氣孔、砂眼、夾渣、裂紋等缺陷，焊接后鋼板的變形應矯正。

Appearance inspection: When making white iron ventilation ducts, the production requirements for the plates, profiles, and other main finished materials used are very strict. The weld seam should undergo visual inspection, and there should be no defects such as pores, sand holes, slag inclusions, cracks, etc. The deformation of the steel plate after welding should be corrected.

材料制作：白鐵皮通風管道加工制作保溫層用聚苯乙烯泡沫板制作，泡沫板密度:40㎏/m3，厚度35㎜(表面溫度不得低于5℃)，保溫層邊部接合部位采用梯臺或榫槽結構，用樹脂粘貼.外表面用鋁箔布裹住，用熱敏膠帶粘貼嚴密，風道外表面不得有結露現象。

Material fabrication: processing and manufacturing of galvanized iron ventilation duct The insulation layer is made of polystyrene foam board, with density of 40 kg/m3 and thickness of 35 mm (surface temperature shall not be lower than 5 ℃). The junction part of the insulation layer edge adopts ladder or mortise structure, which is pasted with resin. The outer surface is wrapped with aluminum foil cloth, and tightly pasted with thermal sensitive tape. The outer surface of the air duct shall be free of condensation.

整齊平直：白鐵皮通風管道加工制作的風道與風口接合用帶保溫層的軟管連接。白鐵皮通風管道制作的風道安裝應平、直，主風道安裝不直度≤1.5㎜/m，不平度≤1㎜/m。白鐵皮通風管道制作和配件表面平整、圓弧均勻、縱向接縫應錯開，咬口縫應緊密，寬度均勻。

Neat and straight: The air duct produced by processing the white iron sheet ventilation duct is connected to the air outlet using a hose with an insulation layer. The installation of the air duct made of white iron sheet ventilation duct should be flat and straight, with an unevenness of ≤ 1.5 mm/m for the main air duct installation and ≤ 1 mm/m. The production of white iron ventilation pipes and accessories should have a flat surface, uniform arc, staggered longitudinal joints, tight bite seams, and uniform width.

配件偏差:濟南鐵皮風管加工制作配件，外徑或外邊長的允許偏差:小于或等于300㎜為-1㎜;大于300㎜為-2㎜.風道系統內所有直角轉彎處均安裝消聲彎頭，消聲彎頭內設鍍鋅鐵板導流片。白鐵皮通風管加工制作的風道采用機械咬口，規整嚴密，接口內表面打玻璃膠.

Deviation of accessories: Jinan iron sheet air duct processing and manufacturing accessories, allowable deviation of outer diameter or outer edge length: less than or equal to 300mm is -1mm; If it is greater than 300mm, it is -2mm. Silencing elbows are installed at all right angle turns in the air duct system, and galvanized iron plate guide vanes are installed inside the silencing elbows. The air duct made of white iron sheet ventilation pipe adopts mechanical bite, which is neat and tight, and the inner surface of the interface is coated with glass glue

白鐵皮通風管道加工制作的四大要求具體事項就講解到這里，您對此還有什么疑惑可以直接來我們官網http://hwzxw.net咨詢看看，希望給您好的解決！

That's all for the four major requirements for the processing and production of white iron ventilation ducts. If you have any doubts about this, please come directly to our official website http://hwzxw.net Consult and hope to provide you with a good solution!